for all ornamentsivory felt a hand sewing needle red embroidery thread cotton balls or fiber-fill (leftover yarn fuzz from pom poms works great, too) pinking shears scissors straight pins a marking pen with water soluble ink a damp paper towel a small paintbrush or pen for the bell ornament a .625 inch jingle bell ivory embroidery thread for the wreath ornament green felt ivory and green embroidery thread an Xacto knife and cutting mat (optional)
1. Print and cut out the ornament templates. Cut a piece of felt that’s twice as long as the ornament template that you’re working with, and position the template on the felt so there’s enough room for you to fold the felt in two when you’re finished tracing the template. Trace around the edge of the template using a water soluble marking pen. To mark where the French knots will go, hold the template and felt against a window so you can see the markings through the felt, and use the water soluble pen to mark where the knots will go.
2. Fold the felt in half and pin together using straight pins. Cut around the edges using pinking shears.
3. Use a damp paper towel to remove any ink that’s left along the edges of the felt. Be sure not to remove the dots that mark where the French knots will go. Unpin the two pieces of felt.
4-5. Make the French knots on the piece of felt with the dot markings, using the dotted side of the felt as the reverse. These images illustrate how to make a French knot, butthis video does a much better job of showing you how to create the stitch. I tie off each knot when I’m finished since the felt is ivory and I don’t want the zig zags of embroidery thread to show through.
6. When you’re finished making the knots, match up the two pieces of felt as closely as you can, with the French knots facing outward, and pin together the pieces. Stitch along the edge of the ornament using a running stitch.
7. You have a few options for attaching the ornament hanger. Tie a 9-10 inch length of red embroidery thread together at the bottom to create the hanger and either 1) sew the hanger in when you come to the top center of the ornament as you’re stitching around (as shown), 2) attach the hanger to the back piece of the ornament before you start stitching the pieces together, or 3) attach the hanger after you’ve finished the ornament.
8. Leave a small opening in one area of the ornament so you can stuff it. You can use cotton balls that have been pulled apart, poly-fill, or leftover trimmings from making pom poms for the stuffing. Push the stuffing into the ornament using a small paintbrush or the end of a pen. After you’ve finished stuffing the ornament, sew it completely closed.
For the Bell Ornament
1. The center star on the bell ornament is made using a long running stitch for each set of points. In order to keep the star in place, make a short running stitch in the center to tack the star in place.
2. To finish the ornament, attach a jingle bell to the center bottom using ivory embroidery thread.
For the Wreath Ornament
1. To cut out the center of the wreath ornament, I like to use an Xacto knife (on a cutting mat) to cut across the diameter of the circle and then use scissors to cut out the center, but you can use scissors to make a hole and cut out from there.
2. Use a whip stitch and ivory embroidery thread to sew together the center edges of the ornament.
3. Stitch together the outer edges of the ornament using a running stitch and ivory embroidery thread. After you’ve stitched about 1 1/2 inches along the edge, stuff the portion that you just stitched using fill and the end of a paintbrush. Stuffing the circle as you go helps prevent gaps in the stuffing.
4. Trace the leaf templates onto green felt, cut out, dab off any remaining ink using a damp paper towel, and sew around the edges of each leaf using a running stitch and green embroidery thread. Attach the leaves to the top center of the wreath ornament.